Introduction to Resistors
CHNM : RESISTORS, INDUCTOR
ITI CHNM Mock Test
RESISTORS, INDUCTOR
1 / 56
Category: Introduction to Inductor and Inductance
In a Transformer the energy is transferred from primary to secondary ____
2 / 56
Category: Introduction to Resistors
Restricting or reducing the flow of electric current to certain level is called___
3 / 56
The purpose of using flux in soldering is to.......
4 / 56
Rheostat is a _____ type of resistor.
5 / 56
_________is a fixed resistor which reduces the flow of electric current by using its resistive element.
6 / 56
The tip used in PCB soldering is ___
7 / 56
Ohm's law is not:
8 / 56
If the two winding transformer the load side is know as _____
9 / 56
If you increase the size of the resistor and keep the voltage the same, what will happen to the current?
10 / 56
Two types of thermistors are___ and _______
11 / 56
What does the letter 'I' stand for in Ohm's Law?
12 / 56
The flux suitable for Copper is____
13 / 56
The unit of inductance is ____
14 / 56
In which side of the PCB the components are mounted?
15 / 56
In a _________ circuit, the total resistance is greater than the largest resistance in the circuit.
16 / 56
The ability of a material to concentrate magnetic flex is called _____
17 / 56
With Ohm's law, if voltage increases and resistance stays the same:
18 / 56
________is a type of resistor in which metal wires are used to reduce the flow of electric current
19 / 56
______ type of resistor in which the resistance changes rapidly with small change in temperature.
20 / 56
Which of the following is generally used to made a voltage dependent resistor?
21 / 56
Transformer is working in the principle of ______
22 / 56
23 / 56
Batteries are generally connected in______
24 / 56
The input side of the single phase transformer is called as
25 / 56
In a ____________ circuit, the total resistance is smaller than the smallest resistance in the circuit.
26 / 56
Which is the most cost efficient connection?
27 / 56
The basic laws for analyzing an electric circuit are :-
28 / 56
Which of the following does not change in a Transformer?
29 / 56
Potentiometer is a ____ type of resistor ?
30 / 56
A light dependent resistors is basically a
31 / 56
Voltage dependent Resistors are used as ___
32 / 56
Which type of substance is used in the base manufacturing of a Printed Circuit Board
33 / 56
Kirchhoff First Law that is sum of current equal to zero at a junction, deals with the conservation of___
34 / 56
Identify the resistors in SERIES.
35 / 56
___ store energy in the form of magnetic field ?
36 / 56
What is the color code for a 560 kΩ resistor with 10% tolerance?
37 / 56
What is the basic unit used to measure the resistance of a resistor?
38 / 56
A transformer core is laminated to ___
39 / 56
Solder wire is a special mixture of different metals in different rations. Which metals are used for making solder?
40 / 56
_________is a type of resistor in which the resistance decreases when the intensity of applied light increases.
41 / 56
KCL is applicable to only _______
42 / 56
In Self Inductance induced voltage is called ___
43 / 56
The melting range of solder is_____
44 / 56
The transformer rating are usually expressed in terms of :
45 / 56
If there are 10 Volts across a 5 Ohm resistor, what is the current?
46 / 56
47 / 56
From which material core of the transformer is constructor?
48 / 56
A PCB is used in____
49 / 56
In the below figure which type of Inductor is mensioned.
50 / 56
51 / 56
According to KVL the algebraic sum of voltages around any closed path in a network is equal to ____________
52 / 56
What is the nominal resistance of a resistor with color code brown-green-black-silver?
53 / 56
Unit of Magnetic flux is:
54 / 56
55 / 56
Kirchhoff's 2nd law is consequence of law of conservation of____
56 / 56
In NTC thermistor on increasing temperature, the resistance
Your score is
The average score is 32%
Restart quiz